Termes les plus fréquents

  • manom√®tre
  • orifice
  • bourdon
  • thermom√®tre
  • transmetteur
  • 802 3
  • transmetteur diff√©rentielle
  • manom√®tre absolue

orifice

10 résultats correspondent au terme orifice.

Plaque à orifice avec support RTJ - Prisma

Plaque à orifice avec support RTJ

Series : APO - RTJ The Plate Holder Assembly is a combination of plate holder and an orifice plate designed for ring tongue joint (RTJ) flanges. The plate holder has a function of holding the orifice plate and also a function as a gasket to prevent[..][...] Lire la suite...

Plaques à orifice - Prisma

Plaques à orifice

Series : PO ¬† Orifice plates are most commonly used primary elements for flow measurement in pipelines based on the principle of measurement of ‚Äėdifferential pressure' created when an obstruction is placed in the fluid flow, due to increase in[..][...] Lire la suite...

Assemblage de rampes de comptage intégrales  - Prisma

Assemblage de rampes de comptage intégrales

Integral Meter Run Assembly Integral Flow Orifice Assembly is used Differential Pressure Transmitter has to be directly mounted on the orifice assembly. This eliminates cost of installation of Differential Pressure Transmitter with impulse piping[..][...] Lire la suite...

Rampes de comptage - Prisma

Rampes de comptage

  Types de rampes de comptage Orifice à bride unies avec Rampes de comptages Orifice à bride unies avec bague de support et rampes de comptage Un tuyau de rampe de comptage est recommandé avec une longueur de 750mm de longueur en amont et de 250mm en aval. Le rampe de comptage à[..] Lire la suite...

Orifice de restriction - Prisma

Orifice de restriction

While single restriction orifices are often sufficient to meet the requirements, there are situations where limitations arise due to process conditions making the single restriction orifices unacceptable. In such situations, use of multiple[..][...] Lire la suite...

Assemblage d'orifices - Prisma

Assemblage d'orifices

Series : AO Typical assemblies : ORIFICE PLATE WITH WELD NECK FLANGE UNION The weld neck flange is normally referred to as " high Hub" flange. It is designed to transfer stresses to the pipe, thereby reducing high stress concentrations at the[..][...] Lire la suite...

Micro Bain d'huile  - Prisma

Micro Bain d'huile

Référence : MOB 250 Le MOB 250 est idéal pour l'étalonnage des orifices multiples et pour les capteurs multiples de types impairs.[...] Lire la suite...

Adjustable Pressure Gauge Snubber - Prisma

Adjustable Pressure Gauge Snubber

Series: PSAN Adjustable Pressure Gauge Snubber   The adjustable pressure gauge dampener draw a unique taper PIN / ORIFICE design for high range of dampening. The dampening can be adjusted to suit the fluid and the pulsation.[...] Lire la suite...

Variable Area Flow Meter - Prisma

Variable Area Flow Meter

It consists of a complete set of orifice plate, carrier rings, bypass lines and rotameter. It is available in flanged or screwed connection and various materials i.e. CS, SS304, SS 304L, SS 316, SS 316L etc. It is mainly recommended for line sizes from 2" to 12"Flow range : From 20 - 200 m3/Hr. TO[..] Lire la suite...

Variable Area Flow Meter

It consists of a complete set of orifice plate, carrier rings, bypass lines and rotameter. It is available in flanged or screwed connection and various materials i.e. CS, SS304, SS 304L, SS 316, SS 316L etc. It is mainly recommended for line sizes from 2" to 12"Flow range : From 20 - 200 m3/Hr.[..] Lire la suite...


Termes les plus fréquemment recherchés : - manomètre - orifice - bourdon - thermomètre - transmetteur - 802 3 - transmetteur différentielle - manomètre absolue